CVE-2026-42781

A vulnerability in the management and VPN web servers for Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause the device to reload unexpectedly, resulting in a denial of service (DoS) condition. This vulnerability is due to incomplete error checking when parsing an HTTP header. An attacker could exploit this vulnerability by sending a crafted HTTP request to a targeted web server on a device. A successful exploit could allow the attacker to cause a DoS condition when the device reloads.

libssh2 through 1.11.1, fixed in commit 1762685, contains a pre-authentication denial of service vulnerability in the SSH_MSG_EXT_INFO handler in src/packet.c that allows a malicious SSH server to cause a client CPU exhaustion loop by sending a crafted extension count value. A malicious server can set nr_extensions to 0xFFFFFFFF during key exchange, causing the client to spin in a tight CPU loop for over 60 seconds because return values from _libssh2_get_string() are unchecked and the session timeout does not apply to CPU-bound loops.

concurrent-ruby is a modern concurrency tools for Ruby. Prior to 1.3.7, Concurrent::AtomicReference#update can enter a permanent busy retry loop when the current value is Float::NAN. The issue is caused by the interaction between AtomicReference#update, which retries until compare_and_set(old_value, new_value) succeeds; Numeric compare_and_set, which checks old == old_value before attempting the underlying atomic swap.; and Ruby NaN semantics, where Float::NAN == Float::NAN is always false. As a result, once an AtomicReference contains Float::NAN, calling #update repeatedly evaluates the caller's block and never returns. In services that store externally derived numeric values in an AtomicReference, this can cause CPU exhaustion or permanent request/job hangs. This vulnerability is fixed in 1.3.7.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: prevent infinite loops caused by the next valid being the same When processing valid within the range [valid : pos), if valid cannot be retrieved correctly, for example, if the retrieved valid value is always the same, this can trigger a potential infinite loop, similar to the hung problem reported by syzbot [1]. Adding a check for the valid value within the loop body, and terminating the loop and returning -EINVAL if the value is the same as the current value, can prevent this. [1] INFO: task syz.4.21:6056 blocked for more than 143 seconds. Call Trace: rwbase_write_lock+0x14f/0x750 kernel/locking/rwbase_rt.c:244 inode_lock include/linux/fs.h:1027 [inline] ntfs_file_write_iter+0xe6/0x870 fs/ntfs3/file.c:1284

In the Linux kernel, the following vulnerability has been resolved: arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults contpte_ptep_set_access_flags() compared the gathered ptep_get() value against the requested entry to detect no-ops. ptep_get() ORs AF/dirty from all sub-PTEs in the CONT block, so a dirty sibling can make the target appear already-dirty. When the gathered value matches entry, the function returns 0 even though the target sub-PTE still has PTE_RDONLY set in hardware. For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered across the CONT range. But page-table walkers that evaluate each descriptor individually (e.g. a CPU without DBM support, or an SMMU without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the unchanged target sub-PTE, causing an infinite fault loop. Gathering can therefore cause false no-ops when only a sibling has been updated: - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared) - read faults: target still lacks PTE_AF Fix by checking each sub-PTE against the requested AF/dirty/write state (the same bits consumed by __ptep_set_access_flags()), using raw per-PTE values rather than the gathered ptep_get() view, before returning no-op. Keep using the raw target PTE for the write-bit unfold decision. Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT range may become the effective cached translation and software must maintain consistent attributes across the range.